If you have been reading about glass transition and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-05-20. Where a claim depends on a specific study, the study is described rather than over-claimed.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
Lyophilized solids are often hygroscopic, so handling occurs in controlled low-humidity areas or glove boxes when the material is exposed. Vials remain sealed with elastomeric stoppers and aluminum crimps until use, because airborne moisture can raise residual water and shorten shelf life. The porous cake is fragile and may crack, shrink, or powder during transport. Personnel typically avoid repeated warming and cooling of sealed units, which can draw moisture through closures. These practices aim to preserve the low water content achieved during drying.
Storage conditions depend on the formulation and the intended shelf life. Many pharmaceutical and biological freeze-dried products are kept at 2–8 °C, while some stable foods and reagents tolerate room temperature. Others require −20 °C or colder to slow chemical degradation or aggregation. Protection from light and oxygen is common because oxidation can continue in the dry state. Stability studies usually monitor potency, appearance, moisture, and reconstitution time over months or years. Predictions from accelerated studies are useful but may not fully capture real-time changes.
Quality control for freeze-dried lots combines visual inspection with instrumental tests. Cake appearance, color, and shrinkage are recorded against a reference, while residual moisture is measured by Karl Fischer titration or loss on drying. Thermal analysis can reveal phase transitions and crystallization events, and X-ray diffraction distinguishes amorphous from crystalline solids. Microbiological tests and container closure integrity checks are also routine for sterile products. Analytical methods must be validated for the matrix, because excipients and low moisture can affect accuracy. Open questions include how best to predict long-term stability from short-term data.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | Freeze-drying, lyophilisation | Lyophilisation is the British spelling; the process is not simple evaporation. |
| Primary drying pressure | 0.05–0.3 mbar | Pressure must remain below the vapor pressure of ice at the product temperature. |
| Sublimation temperature | Below 0 °C | Ice changes directly to vapor while the product remains frozen. |
| Typical shelf temperature | −40 to −10 °C | Exact setting depends on formulation critical temperature and equipment. |
| Cycle duration | 12–72 hours | Time varies with fill volume, formulation, and dryer performance. |
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Lyophilized products are typically hygroscopic and require protection from moisture during storage. Manufacturers seal them in glass vials, often under vacuum or an inert gas such as nitrogen. The container closure system, including the stopper and crimp seal, must prevent water vapor ingress. Storage temperature varies from controlled room temperature to refrigerated or frozen conditions, depending on the formulation. Humidity-controlled environments are essential because even brief exposure to ambient air can degrade the product.
Stability of a lyophilized product depends on its glass transition temperature, the temperature at which the amorphous cake transitions from a glassy to a rubbery state. Storage below this temperature minimizes molecular mobility and slows chemical degradation. If the storage temperature exceeds the glass transition temperature, the cake may collapse, shrink, or become sticky. Accelerated stability studies at elevated temperatures and humidity help predict shelf life, but they do not always reflect real-time behavior. Residual moisture content also plays a critical role in long-term stability.
A typical cycle begins with freezing, sometimes including an annealing step to control ice crystal size. Freezing conditions influence the pore network that later allows vapor escape. During primary drying, shelf temperature and chamber pressure are set so heat enters the product while its temperature stays below the collapse or eutectic point. Secondary drying then raises the shelf temperature to desorb bound water and lower residual moisture. Cycle design depends on formulation, fill volume, container type, and equipment capability.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Corin, also called atrial natriuretic peptide-converting enzyme, is a protein that in humans is encoded by the CORIN gene. Human corin, a polypeptide of 1042 amino acids, consists of an N-terminal cytoplasmic domain, a transmembrane domain and an extracellular region with two frizzled-like domains, eight LDL receptor-like domains, a scavenger receptor-like domain and a C-terminal trypsin-like serine protease domain. Corin is synthesized as a zymogen that is activated by PCSK6. Corin exhibits a trypsin-like catalytic activity favoring basic residues at the P1 position. Human corin contains 19 N-glycosylation sites. N-glycans promote corin expression on the cell surface and protect corin from metalloproteinase-mediated shedding.
In plants, nitrogen is first assimilated into organic compounds in the form of glutamate, formed from alpha-ketoglutarate and ammonia in the mitochondrion. For other amino acids, plants use transaminases to move the amino group from glutamate to another alpha-keto acid. For example, aspartate aminotransferase converts glutamate and oxaloacetate to alpha-ketoglutarate and aspartate. Other organisms use transaminases for amino acid synthesis, too. Nonstandard amino acids are usually formed through modifications to standard amino acids. For example, homocysteine is formed through the transsulfuration pathway or by the demethylation of methionine via the intermediate metabolite S-adenosylmethionine, while hydroxyproline is made by a post translational modification of proline. Microorganisms and plants synthesize many uncommon amino acids. For example, some microbes make 2-aminoisobutyric acid and lanthionine, which is a sulfide-bridged derivative of alanine. Both of these amino acids are found in peptidic lantibiotics such as alamethicin. However, in plants, 1-aminocyclopropane-1-carboxylic acid is a small disubstituted cyclic amino acid that is an intermediate in the production of the plant hormone ethylene.
Both the thyroid and adrenal glands can be infiltrated. It is estimated that 10–20% of people with amyloidosis have hypothyroidism. Adrenal infiltration may be harder to appreciate given that its symptoms of orthostatic hypotension and low blood sodium concentration may be attributed to autonomic neuropathy and heart failure. "Amyloid deposits occur in the pancreas of people who also have diabetes mellitus, although it is not known if this is functionally important. The major component of pancreatic amyloid is a 37-amino acid residue peptide known as islet amyloid polypeptide or 'amylin.' This is stored with insulin in secretory granules in [beta] cells and is co secreted with insulin." (Rang and Dale's Pharmacology, 2015.)
Sources: en.wikipedia.org
Arterial damage results from white blood cell invasion and inflammation within the wall. CRP is a general marker for inflammation and infection, so it can be used as a very rough proxy for heart disease risk. Since many things can cause elevated CRP, this is not a very specific prognostic indicator. Nevertheless, a level above 2.4 mg/L has been associated with a doubled risk of a coronary event compared to levels below 1 mg/L; however, the study group in this case consisted of patients who had been diagnosed with unstable angina pectoris; whether elevated CRP has any predictive value of acute coronary events in the general population of all age ranges remains unclear. Currently, C-reactive protein is not recommended as a cardiovascular disease screening test for average-risk adults without symptoms. The American Heart Association and U.S. Centers for Disease Control and Prevention have defined risk groups as follows:
As the salt of a weak base (ammonium) and a weak acid (acetic acid), is often used to create a buffer solution. Ammonium acetate is volatile at low pressures. Because of this, it has been used to replace cell buffers that contain non-volatile salts in preparing samples for mass spectrometry. It is also popular as a buffer for mobile phases for HPLC with ELSD and CAD-based detection for this reason. Other volatile salts that have been used for this include ammonium formate. When dissolving ammonium acetate in pure water, the resulting solution typically has a pH of 7, because the equal amounts of acetate and ammonium neutralize each other. However, ammonium acetate is a dual component buffer system, which buffers around pH 4.75 ± 1 (acetate) and pH 9.25 ± 1 (ammonium), but it has no significant buffer capacity at pH 7, contrary to common misconception.
The word analgesic derives from Greek an- (ἀν-, "without"), álgos (ἄλγος, "pain"), and -ikos (-ικος, forming adjectives). Such drugs were usually known as "anodynes" before the 20th century. Analgesics are typically classified based on their mechanism of action. Paracetamol, also known as acetaminophen, is a medication used to treat pain and fever. It is typically used for mild to moderate pain. In combination with opioid pain medication, paracetamol is now used for more severe pain such as cancer pain and after surgery. It is typically used either by mouth or rectally but is also available intravenously. Effects last between two and four hours. Paracetamol is classified as a mild analgesic, and is generally safe at recommended doses. Nonsteroidal anti-inflammatory drugs (NSAIDs) are a drug class that groups together drugs that decrease pain and lower fever, and, in higher doses, decrease inflammation. The most prominent members of this group of drugs—aspirin, ibuprofen, naproxen, and diclofenac—are all available over the counter in most countries.
Sources: en.wikipedia.org
The main change is sublimation, in which ice becomes water vapor without melting into liquid water. This occurs when the chamber pressure is held below the vapor pressure of ice while mild heat is supplied. The result is a dry, porous solid that retains much of its original shape.
Freezing determines ice crystal size, solute distribution, and the pore network left after drying. A slow or fast freezing rate can produce different cake structures and affect reconstitution. It also sets whether the formulation follows an amorphous or crystalline drying path.
It removes most free water during primary drying and part of the bound water during secondary drying. A small residual moisture content often remains and is specified for each product. Complete removal is generally neither practical nor desirable for stability.
Karl Fischer titration is widely used because it is specific for water and works at low levels. Loss on drying is simpler but less specific, since volatile solvents or decomposition products can also be lost.